Posted in

How to install other cable accessories?

If you’ve ever worked on a power distribution, industrial automation, or electrical infrastructure project, you know that cable accessories don’t get nearly enough credit. You can run the highest-quality cable, bury it correctly, and connect it to the right equipment—but if the accessories that seal, terminate, and support it are installed wrong, the whole system fails. Over the past 12 years, I’ve worked as an “Other Cable Accessories” supplier—meaning we cover everything from cable glands and lugs to cable ties, ferrules, and sealing fittings that don’t fit into the big, well-known termination or joint accessory categories. I’ve seen first-hand how a poorly installed cable gland can cause water intrusion that shuts down a mining site for 3 days, or how a misapplied ferrule can cause a control panel short that costs a manufacturing plant $20,000 in downtime. Today, I’m breaking down the step-by-step, field-tested process to install these “other” cable accessories right—no fancy tools, no overly complicated tricks, just real advice from someone who’s spent more time fixing bad installs than doing perfect ones. Other Cable Accessories

First, let’s get one thing straight: “other cable accessories” isn’t a throwaway term. It’s the catch-all for every component that supports a cable’s reliability beyond the core conductor and insulation. That includes cable glands (for securing cables to enclosures, junction boxes, or equipment), lugs and terminals (for connecting cable ends to bus bars or breakers), cord grips (for heavy-duty applications where tension pulling on the cable is a risk), ferrules (for crimping onto small wire ends to prevent fraying inside terminal blocks), cable ties and cable clamps (for organizing and securing cable runs), sealing plugs (for filling unused cable entry points in enclosures), and cable markers (for labeling runs to simplify future maintenance). Each has its own specific installation rules, but the base steps I’m sharing will work for 90% of these accessories, with notes on where to adjust for specialized use cases.

Before you touch a single accessory, stop and do two critical pre-install checks that most electricians skip (and that’s why so many installs fail). First, match the accessory to your cable and environment. This isn’t just grabbing the generic gland from your truck. If you’re working in an outdoor agricultural site that’s exposed to constant moisture and livestock (which can chew through cable, but also knock equipment around), you need a stainless steel cable gland, not a plastic one. If your cable has a 10mm outer diameter (OD), a 12mm gland will leave a gap that lets water in—a common mistake. Too small, and you’ll crack the gland when you tighten it. Lugs are another easy one: a 4AWG copper cable needs a lug rated for 4AWG, not a generic 2-6AWG lug that might be too loose or have a crimp barrel that’s too small to hold the conductor. For ferrules, check the wire gauge marked on the ferrule packaging—some are sized for solid wire, others for stranded, and using the wrong one will lead to frayed wires inside a terminal block.

Second, prep your cable correctly. I’ve seen so many electricians cut a cable, strip the insulation, and then yank it into place without smoothing the cut end, resulting in nicks in the insulation or exposed conductor strands that cause shorts. For prep: start by measuring the length of insulation you need to strip. For example, when installing a lug, you only need to strip enough insulation to fit into the lug’s barrel—usually 1/8 to 1/4 inch more than the barrel length. Stripping too much leaves exposed conductor near the connection point, while stripping too little means you can’t fully crimp the lug. Use a cable stripper, not a utility knife, to avoid nicking the conductor—nicks weaken the wire and can cause it to break under tension or electrical load. If you’re working with armored cable, carefully remove the armor layer with a armor stripper, being careful not to cut the inner insulation. For cord grips (used for heavy industrial cable pulling, like on cranes or conveyor systems), you’ll need to leave extra length of outer jacket to feed into the grip’s tension relief area—this prevents pulling the cable out of the connection when force is applied.

Now, let’s walk through the step-by-step installation process, using the most common accessories as examples. Let’s start with cable glands, the most frequently installed “other” accessory and the number one cause of water and debris intrusion in enclosures.

Step 1: Thread the gland body through the enclosure’s cable entry hole. First, put any washers or sealing gaskets that came with the gland on first—don’t skip the gasket. The gasket creates a watertight seal between the gland and the enclosure, and leaving it out is like building a boat without a hull seal. Thread the gland body through the hole from the inside or outside, depending on your installation. For most outdoor enclosures, you thread it from the outside so the watertight seal is on the external side, keeping moisture out before it reaches the enclosure interior.

Step 2: Insert the cable through the gland, then adjust the cable position. Leave enough length of cable sticking out of the gland to work with, but not so much that it gets in the way of tightening the gland’s components. If the gland has multiple seals (some have inner seals for cable insulation and outer seals for the gland body), make sure the cable sits centered between the seals—this creates an even seal around the cable, no gaps.

Step 3: Tighten the gland’s components in the correct order. This is where most people mess up. Tighten the locknut first, then the compression nut, not the other way around. The locknut holds the gland body in place on the enclosure, while the compression nut squeezes the inner seal against the cable to create a watertight grip. Tighten the compression nut until it’s snug, then give it an extra quarter turn—don’t over-tighten, as this can crack the plastic or rubber seal or distort the cable’s insulation, leading to a weak point. For IP67 or higher rated glands, you’ll need to use a torque wrench (usually 15-20 Nm for standard 10-16mm glands) to get the seal right—always check the manufacturer’s specs, because that’s non-negotiable for meeting ingress protection ratings.

Next, let’s cover lugs and terminals, which are used for connecting cables to bus bars, breakers, or other equipment. Bad lug crimps are a leading cause of electrical fires, because loose connections create resistance that heats up and melts insulation.

Step 1: Clean the cable conductor and lug barrel. Oxidation on copper or aluminum conductors prevents a tight, low-resistance crimp. Use a steel wool brush or electrical contact cleaner to scrub the conductor until it’s shiny, and wipe out the inside of the lug barrel with a clean cloth. This simple step reduces connection resistance by up to 30%, extending the life of the connection.

Step 2: Insert the conductor into the lug barrel. Make sure the entire stripped conductor is inside the barrel, with no strands sticking out. Strands sticking out can cause a short circuit between the lug and the adjacent terminal. For lugs with two crimp points (most standard lugs: one on the barrel part that holds the conductor, one on the insulation part just behind the barrel), insert the conductor so that 1/8 inch of insulation is inside the barrel, to create a strain relief point.

Step 3: Crimp correctly. Use a crimping tool rated for the lug size and wire gauge. A generic pliers won’t work—you need a hydraulic or ratchet crimp tool that matches the lug type (uninsulated, insulated, butt, or ring terminal). For uninsulated lugs, crimp the point closest to the conductor first, then the point closest to the insulation. Squeeze the crimp tool until it clicks, then hold it for 2 full seconds to ensure a permanent, tight crimp. Never crimp a lug twice in the same spot—this weakens the metal and can cause the lug to break under tension.

For ferrules, used for small stranded wires (18AWG or smaller) that go into terminal blocks, the process is simple but easy to mess up. Slide the ferrule onto the stripped wire end, making sure it covers all strands. Use a small ferrule crimp tool to squeeze the ferrule firmly until it’s secured. The ferrule should hold all strands together neatly—no frayed ends sticking out. If the ferrule slides off the wire after crimping, you used the wrong size ferrule (too small) or didn’t squeeze hard enough.

Now, let’s talk about specialized accessories, because not all installs are the same. For outdoor or harsh environments (subzero temperatures, high humidity, saltwater), make sure all metal accessories are hot-dip galvanized or stainless steel—galvanized steel will rust in coastal areas within 2 years, leading to broken glands and equipment damage. For cord grips used in pulling high-voltage or heavy-duty cables, test the grip’s tension after installation by pulling gently on the cable with your body weight—if the cable moves, the grip is too loose; tighten the set screws slightly. For cable markers, install them every 3 meters along a cable run, at every junction box, and at both ends of a cable—this saves hours of troubleshooting when you need to find a specific cable later.

I know there’s a lot to remember, so here are three common mistakes I see even experienced electricians make, and how to avoid them: First, skipping a sealing gasket on cable glands. I once had a customer come back to us with 12 failed installations because they used glands without gaskets in a rainforest site—water was getting into the enclosures through the gaps around the glands, shorting out control systems. Always use the gasket that comes with the gland, no exceptions. Second, using a utility knife to strip cable insulation. A utility knife can nick up to 20% of the conductor strands, weakening the cable’s capacity to carry current. Invest in a $10 cable stripper—it will pay for itself in reduced rework and fewer failed connections. Third, not checking the accessory’s rating for the specific application. A cable gland rated for IP54 (dust and splash-proof) is not suitable for a pool pump enclosure, which needs IP67 (submersible). Always check the manufacturer’s spec sheet, which is in every product package we ship with all our accessories.

Over the years, I’ve built our business on solving the small, annoying problems that come with cable accessories. Whether you’re a electrician working on residential wiring, a industrial maintenance manager troubleshooting a plant, or a contractor building a new infrastructure project, getting these “other” accessories right is what makes the difference between a job that works for 5 years and one that works for 20. If you have questions about matching accessories to your project, need a bulk order, or want a free sample to test before you buy, I’m here to help. Our team has 15 years of experience working with electrical contractors, industrial sites, and infrastructure projects, and we’re happy to walk you through any step of the installation process or recommend the right accessory for your specific needs. Reach out to us to discuss your project, and let’s make sure your next cable installation lasts.

Box Type Substation References

  1. National Electrical Code (NEC), Article 300 (Wiring Methods, Components, and Equipment for Electrical Circuits)
  2. International Electrotechnical Commission (IEC) Standard 61386 (Conduit Systems for Electrical Installations)
  3. Cable Installation Best Practices Guide, Electrical Construction Maintenance (EC&M) Magazine, 2022 Edition

Jiangsu Yuantong Electric Co., Ltd.
As one of the most professional cable accessories manufacturers and suppliers in China, we also support customized service. We warmly welcome you to wholesale bulk cable accessories for sale here from our factory. For more information, contact us now.
Address: No.68 Xiyuan Avenue, Hai’an Industrial Park, Hai’an City, Jiangsu Province, China
E-mail: aaron@jsytelectric.com
WebSite: https://www.yuantongtransformer.com/