If you’ve ever stood on a tropical beach, felt the warm, sun-warmed water lapping at your ankles, and wondered why we don’t tap that constant, free heat to power homes and businesses, you’re not alone. For over a century, engineers and energy leaders have been asking the same question—and today, ocean thermal energy conversion (OTEC) is moving from a theoretical concept to a viable, scalable power source. As a power generation equipment supplier with deep roots in renewable energy infrastructure, I’ve spent years working with teams to turn OTEC’s promise into tangible, reliable systems, and I’m here to break down exactly how it works, why it matters, and how you can be part of bringing this technology to life. Power Generation Equipment

Let’s start with the basics that make OTEC possible. The oceans don’t just hold water—they hold a consistent thermal gradient, a fancy way of saying “difference in temperature” between surface waters and deep ocean waters. In tropical regions, where the sun beats strongest, surface water stays around 25 to 30 degrees Celsius (77 to 86 degrees Fahrenheit) year-round. Just 1,000 meters (3,280 feet) below the surface, that water plummets to 4 to 7 degrees Celsius (39 to 45 degrees Fahrenheit)—a sharp, reliable gap that never stops. That temperature difference is the core of OTEC; without it, the whole system can’t generate power. We typically target areas within 20 degrees of the equator, where this gradient is consistent enough to support round-the-clock operation, no sun or wind required.
Now, how do we turn that temperature gap into electricity? There are two main OTEC cycles in use today, and both rely on a working fluid—something that boils at a much lower temperature than water, perfect for capturing small temperature differences. The first, and most common for commercial systems, is the closed-cycle OTEC. Here’s how it works step by step, from start to finish. First, we pull warm surface ocean water into a heat exchanger—think of it as a giant, specialized radiator made of corrosion-resistant titanium, because saltwater eats through most metals. This warm surface water doesn’t mix with the working fluid, because if it did, we’d have to purify all the water we use, which would add massive costs. Instead, the heat from the surface water passes through the heat exchanger’s walls and warms the working fluid, which is usually ammonia, or sometimes propane or another low-boiling-point fluid. Ammonia’s boiling point is around -33 degrees Celsius (-27 degrees Fahrenheit), so even warm surface water is more than enough to turn it into a low-pressure gas.
Once the ammonia turns to gas, it expands rapidly, and that expansion drives a turbine—connected directly to a generator, the same kind we use in other power plants, just sized for OTEC’s slower, steadier flow. That turbine spins, and suddenly we have electricity. The process isn’t done yet, though. After the ammonia gas spins the turbine, it’s still warm, and we need to cool it back down to a liquid so we can reuse it. That’s where the cold deep ocean water comes in. We pull the 4-degree Celsius deep water up through a second, even larger heat exchanger. This cold water wraps around the ammonia lines, cooling the gas back into a liquid (a process called condensation), and then we pump the liquid ammonia back to the first heat exchanger to repeat the whole cycle. The whole system runs nonstop, 24/7, because the thermal gradient never changes—no matter if it’s noon or midnight, summer or winter, the surface and deep water temperatures stay consistent.
The second cycle, open-cycle OTEC, works a little differently, and it’s ideal for areas where we also need to produce fresh water, not just power. Instead of a separate working fluid, open-cycle uses the warm surface ocean water itself as the working fluid. First, we put the warm surface water into a low-pressure chamber, where the air pressure is so low that water boils at only 25 degrees Celsius (the same as our starting surface water temperature). When the water boils, it turns into low-pressure steam, which expands and drives a turbine to generate electricity. Then, we take that steam and cool it with deep cold water, which condenses the steam into pure, fresh water. That’s a huge bonus for coastal communities in arid tropical regions, where fresh water is just as scarce as power. The downside? Open-cycle is less efficient than closed-cycle, and it’s harder to scale for large power grids, so most commercial OTEC projects right now are closed-cycle.
Now, let’s talk about the infrastructure that makes all this happen—this is where a power generation equipment supplier like me comes in, because every part of an OTEC system is specialized, off-the-shelf for fossil fuel power plants won’t cut it. First, the cold water pipe: this is the biggest, most expensive part of an OTEC system. It’s a long, flexible or rigid pipe that runs 1,000 meters from the surface down to the cold deep water. It has to be strong enough to withstand the pressure at those depths, corrosion-resistant to saltwater, and flexible enough to handle ocean currents and tides. For small, near-shore systems, we sometimes use rigid steel pipes lined with plastic, but for larger offshore projects, we use reinforced, fiber-composite pipes that are lighter and cheaper to deploy. I’ve worked on projects where we had to test these pipes for a year straight in rough seas to make sure they don’t leak or break—one small tear can mess up the entire thermal gradient and shut down the whole system.
Next, the heat exchangers. These are the heart of the OTEC cycle, and they have to be incredibly efficient. We use plate heat exchangers for most closed-cycle systems, because they have a large surface area to maximize heat transfer between the seawater and the working fluid. But because saltwater causes biofouling—barnacles, algae, and other sea life that stick to the pipes and block heat flow—we have to add anti-fouling systems. That means regular flushing with hot water (from the surface, which is warm enough to kill biofilm) or even chemical treatments that are safe for marine life. As a supplier, we’ve partnered with marine biologists to develop anti-fouling systems that don’t harm coral or fish, which is a big priority for OTEC’s green credentials.
Then there’s the power conversion and grid integration equipment. The turbine and generator are similar to what you’d find in a natural gas plant, but they’re sized to run at a slower, steadier speed—OTEC doesn’t have the sudden steam surges that coal or gas plants use. We also need transformers that can convert the low-voltage power from the generator to the high-voltage needed for transmission to the grid. For offshore systems, where the OTEC plant is on a floating platform, we also have to account for wave motion—our equipment has to be mounted on stabilization systems so it doesn’t shift and cause damage during storms.
A lot of people ask: why bother with OTEC when we have wind and solar? That’s a fair question, and OTEC isn’t here to replace wind or solar—it’s here to complement them. Wind and solar are intermittent: they only generate power when the wind blows or the sun shines. OTEC runs 24/7, with a capacity factor of around 90%—that’s almost as reliable as nuclear power, way higher than wind’s 35% or solar’s 25%. For island nations, which rely on expensive diesel generators for most of their power, OTEC is a game-changer. Diesel costs can be $0.30 to $0.50 per kilowatt-hour, while OTEC can generate power for $0.10 to $0.15 per kilowatt-hour, once the initial infrastructure is in place. That’s a huge cost savings over time, and it cuts down on the carbon emissions from diesel, which is a win for the environment.
We’re already seeing OTEC projects come online around the world. In Hawaii, the Natural Energy Laboratory of Hawaii Authority has a 100-kilowatt OTEC test plant that’s been running since 2015, proving that the technology works. In Taiwan, a 1-megawatt closed-cycle OTEC plant is set to come online in 2025, and in the Maldives, a 2-megawatt plant is in the planning stages to power a resort and supply fresh water. For small island developing states (SIDS) that don’t have their own fossil fuel reserves, OTEC is the only renewable energy source that can provide baseload power at a scale that works for their small grids.
But OTEC isn’t without its challenges. The biggest one is cost. The initial capital for an OTEC system—especially the cold water pipe and the floating platform for offshore systems—can run $5 to $10 million per megawatt, which is higher than solar’s $1 to $2 million per megawatt. But over a 25 to 30 year lifespan, the lower operating costs and no fuel costs make it competitive. Another challenge is marine impact: while OTEC doesn’t burn fuel or emit greenhouse gases, pumping cold, nutrient-rich deep water to the surface can change local water chemistry. The good news is that we’re now modifying OTEC systems to use that nutrient-rich water for aquaculture—growing fish, seaweed, and shellfish right next to the OTEC plant, using the excess cold water. That turns OTEC from a single-purpose power plant into a multi-use marine facility, which brings in extra revenue to offset costs.
As a power generation equipment supplier, my team works with project developers, engineering firms, and governments to design and build custom OTEC systems that fit their needs. Whether you’re an island nation looking to replace diesel generators, a coastal city wanting to add baseload renewable power, or a research institution testing new OTEC technology, we can provide the heat exchangers, cold water pipes, turbines, and grid integration equipment you need. We don’t offer one-size-fits-all solutions—every OTEC project is unique, depending on water depth, grid size, and whether you want fresh water as a byproduct. If you’re considering OTEC for your project, we can work with you to assess your site, calculate costs, and deliver reliable, durable equipment that’s built to last in harsh marine environments.

OTEC is one of the most underrated renewable energy technologies out there, and it’s only going to grow as countries and island nations look for ways to cut carbon emissions and lower energy costs. It’s not a distant dream—it’s a proven technology that’s already powering small communities and will soon power larger grids. If you’re interested in learning more about how OTEC works, or how we can supply the equipment to bring your OTEC project to life, reach out to our team to start a conversation about your power generation needs.
Power Transmission and Distribution Equipment References
- US Department of Energy. (2022). Ocean Thermal Energy Conversion: Technology Overview.
- International Energy Agency. (2023). Renewable Energy Technology Trends: Ocean Energy.
- Natural Energy Laboratory of Hawaii Authority. (2021). OTEC Test Plant Operations & Performance Data.
- Global Ocean Energy Council. (2022). Commercial OTEC Project Deployment Status Report.
Chongqing Lushun Scientific & Technological Development Co., Ltd.
Chongqing Lushun Scientific & Technological Development Co., Ltd. is one of the most reliable power generation equipment manufacturers and suppliers in China, featured by quality products and good price. Please rest assured to buy customized power generation equipment made in China here from our factory. Welcome to contact us for quotation.
Address: No.15 Factory Building, Sendi Times Industry Base, Jiulongpo District, Chongqing, China
E-mail: sale7@lushuntec.com
WebSite: https://www.cqlushun.com/