Posted in

What is an inductor’s impedance at different frequencies?

As an inductor supplier who’s spent the last 12 years working with engineers, product designers, and hobbyists—answering late-night questions about why an inductor fails in a 500MHz circuit, or why a 1µH part works for a power supply but not a RF amplifier—I can tell you this: most folks who use inductors only think about their impedance at one frequency. That’s a mistake. Inductors don’t have a single, static impedance. Their behavior shifts like a chameleon across the frequency spectrum, and understanding that is how you avoid circuit headaches, rework costs, and even product failures. Inductor

Let’s start with the basics: what is impedance, anyway? For anyone who’s dabbled in electronics, you might know resistance is opposition to direct current (DC) flow. Impedance is a broader term for total opposition to alternating current (AC) flow, and for inductors, it’s not just resistance—it’s a mix of two things: inductive reactance and parasitic elements that kick in at high frequencies.

At DC, the story is simple. An ideal inductor acts like a short circuit, right? It lets DC current pass with almost no resistance, just the tiny ohmic resistance of its wire winding. But real inductors aren’t ideal. Even at DC, there’s a small amount of DC resistance (DCR) from the copper wire we use to wind our parts—something we optimize for every product we build, because too much DCR wastes power in power converters. But for low-frequency AC, this is irrelevant, because inductive reactance becomes the dominant force.

Inductive reactance (XL) is calculated with the formula XL = 2πfL, where f is frequency in hertz, and L is inductance in henries. Let’s use a concrete example from our product line: our standard 1µH power inductor (part number IND-1005-1R0) is made with 32 AWG copper wire. At 1kHz, that formula gives XL = 2 * 3.1416 * 1000 * 0.000001 = ~0.00628 ohms. Compare that to its DCR of 0.02 ohms—so at 1kHz, the inductor’s impedance is mostly DCR, not reactance. That’s a key point: at low frequencies, below the inductor’s self-resonant frequency (SRF), impedance rises linearly with frequency. The lower the frequency, the smaller the reactance, so the closer impedance is to DCR.

Now move up to the audio range, say 10kHz. For that same 1µH inductor, XL becomes 0.0628 ohms. It’s still small, but it’s now twice the DCR. At 100kHz, XL jumps to 0.628 ohms—30 times the DCR. By 1MHz, XL is 6.28 ohms, which is hundreds of times the DCR. Here’s where the linear trend holds: every time frequency doubles, XL doubles. That’s how inductive reactance behaves in the low-to-mid frequency range, up to a critical point we call the self-resonant frequency.

This is where most people get caught off guard. Inductors aren’t just a coil of wire—they have parasitic capacitance between the windings, and even between the core and the windings. That’s a hidden element: a parallel capacitance (C) that forms an LC circuit with the inductor’s own inductance. The SRF is the frequency where the inductive reactance and this parasitic capacitive reactance (XC = 1/(2πfC)) are equal in magnitude. At SRF, they cancel each other out—so what was rising impedance suddenly stops.

Take that same 1µH power inductor: its SRF is 12MHz. Let’s calculate the capacitive reactance at SRF: XC = 1/(2π12,000,000 * C). We know XL at SRF equals XC, so 2π12,000,0000.000001 = 1/(2π12,000,000*C). Solving for C gives ~1.76pF for the parasitic capacitance of this part. That’s tiny, but it has a big effect once you’re above SRF.

Above the self-resonant frequency, the parasitic capacitance dominates. Now the inductor behaves like a capacitor, not an inductor. Its impedance starts to drop as frequency increases, following the capacitor’s reactance rule: XC = 1/(2πfC). So for that 1µH inductor, once you pass 12MHz, going to 24MHz (double the frequency) means XC is half of what it was at SRF, so impedance drops by half. Go to 100MHz, and impedance is way lower than the impedance at SRF.

I see this mistake all the time with RF engineers. A few years back, a customer called us in a panic: their 433MHz remote control circuit kept failing, even though they used a 1µH inductor as a choke. They’d picked the part because its datasheet listed 1µH, but they didn’t check the SRF. Our IND-1005-1R0’s SRF is 12MHz—way lower than 433MHz. At 433MHz, that part’s impedance is capacitive, not inductive. It wasn’t choking the RF signal like they needed; it was letting it pass. We swapped them for our high-frequency RF inductor, part number IND-0806-1R0, which has an SRF of 85MHz, and their circuit worked perfectly. That’s the kind of avoidable problem that comes from only looking at an inductor’s inductance and not its impedance across frequencies.

Let’s break down another example: a 10µH inductor, which is common in DC-DC converters. Its SRF is lower, right? Because SRF is inversely proportional to the square root of L*C, so higher inductance means lower SRF. Our IND-1210-10M (10µH power inductor) has an SRF of 2.8MHz. At 1kHz, XL is 0.0628 ohms, DCR is 0.05 ohms—again, DCR is dominant. At 100kHz, XL is 6.28 ohms, which is bigger than DCR. At 2.8MHz (SRF), impedance is at its peak, around 75 ohms. Above 2.8MHz, it drops, acting like a capacitor. So if you’re using that 10µH inductor in a 5MHz DC-DC converter, you’re losing the inductive choke effect because you’re above SRF. That means more ripple on your output voltage, which could damage your load.

Parasitic elements aren’t just the parallel capacitance, either. There’s also series resistance from the wire and core loss (if it’s a ferrite core). Core loss becomes more significant at high frequencies too—especially with ferrite materials, which can have reduced permeability at higher frequencies. For high-frequency applications, we use different core materials, like powdered iron or ceramic, to minimize that. For example, our IND-0806-1R0 uses a ferrite core optimized for 10MHz to 1GHz, so its impedance stays inductive in that range, whereas a standard power inductor would start to behave capacitively at 12MHz.

Another real-world scenario: audio amplifiers. In a crossover network, inductors are used to block low frequencies from the tweeters, right? Wait no—actually, a series inductor in a crossover acts as a low-pass filter, letting bass frequencies go to the woofers. If you pick the wrong inductor, it can mess up the frequency response. Let’s say a designer picks a 1mH inductor for a car audio crossover, thinking XL = 2π20Hz0.001 = ~0.125 ohms, which is perfect for blocking high frequencies. But what’s the SRF of that inductor? If it’s a standard 1mH power inductor, SRF is around 1MHz. That means at 20kHz (the upper end of audio), which is close to SRF, the impedance is lower than calculated, so it doesn’t filter high frequencies as intended. We have audio-grade inductors with SRF above 20kHz, so their impedance stays inductive across the entire audio spectrum, giving clean crossover performance.

Now, let’s talk about how we measure this at our factory. When we test each inductor we ship, we don’t just measure inductance at 1kHz—we sweep frequencies from 10Hz up to 1GHz using an impedance analyzer. That’s the only way to get a full picture of its impedance profile. A lot of budget inductors only test at a single frequency, which is why they can fail in real circuits. We include full frequency impedance curves in every datasheet we send to customers, so they don’t have to guess.

Here’s the takeaway you need, whether you’re a hobbyist breadboarding a circuit or a design engineer laying out a production board: impedance varies with frequency, so you can’t use a low-frequency inductor in a high-frequency application, and vice versa. If you need an inductor to act as a choke in a 100MHz RF circuit, you need a part with an SRF well above 100MHz. If you’re using it in a 50Hz power supply, you don’t care about SRF—you just need low DCR.

I’ve seen too many projects get delayed, or even scrapped, because someone picked the wrong inductor without checking its frequency-dependent impedance. Last year, a startup working on a 2.4GHz IoT device came to us with a prototype that had range issues. Their engineer had used a standard 2.2µH inductor for an antenna matching network, thinking inductance was all that mattered. That part’s SRF was only 8MHz, so at 2.4GHz, it was a capacitor, not an inductor. We supplied them with our 2.2µH RF inductor, SRF 1.2GHz, and their range doubled overnight.

So, if you’re designing a new circuit, or troubleshooting a part that’s not working as expected, don’t stop at the datasheet’s single-number inductance. Look at the impedance across your circuit’s operating frequency. If you’re not sure which inductor fits your frequency range, or you need help navigating our product line’s impedance profiles, we’re here to help. We’ve worked with everything from small hobby projects to large-scale industrial power systems, and we can recommend the right inductor for your specific frequency needs, even if you’re not sure where to start.

Our team has 15 years of experience in inductor design and testing, so we can walk you through impedance curves, SRF specs, and tradeoffs between DCR and high-frequency performance. Whether you need a power inductor for a 50kHz converter, a RF inductor for a 900MHz sensor, or an audio-grade inductor for a speaker system, we can get you the right part fast, and support you through every step of your design. Don’t let a frequency mismatch derail your project—reach out to our team today to discuss your requirements, and we’ll help you find the perfect inductor for your application.

Inductor References

  1. Floyd, T. L. (2017). Electronic Devices (10th ed.). Pearson Education.
  2. El-Hawary, M. E. (2018). Fundamentals of Electrical Engineering. CRC Press.
  3. IEEE Standard for Definitions of Terms for Ferrite Microwave Materials. (2019). IEEE Std 180-2019.
  4. Maniktala, S. (2011). Switching Power Supplies A to Z (2nd ed.). Newnes.
  5. Van Valkenburg, M. E. (2016). Network Analysis (3rd ed.). Pearson.

Dongguan Hensiron Electric Co., Ltd.
As one of the most professional inductor suppliers in China, we have world-leading production equipment and strong manufacturing capabilities. Please feel free to buy high quality inductor made in China here from our factory. Customized orders are welcome.
Address: Building 4, Xinxing Industrial Zone, Wangao Road, Wanjiang Street, Dongguan City, China
E-mail: jessica@dghensiron.com
WebSite: https://www.dghensiron.com/