If you’ve ever walked into a room that feels “dead”—where every word echoes down the hallway and music gets muddy the second it leaves the speakers—you know how much bad acoustics can ruin a space. As someone who’s been working with felt acoustic panels for the last eight years, starting out as a small supplier to local cafes and recording studios before expanding across North America, I get asked this question all the time: How do my panels stack up against the other acoustic materials out there? It’s a fair question, too. When you’re budgeting for a space that’s used for meetings, performances, or even just working from home, you don’t want to waste money on something that doesn’t do the job. Let’s break this down the way I do for every customer who walks through our showroom or sends an email: no jargon, just hard data and real-world experience. Felt Acoustic Panel

First, let’s start with the basics of sound absorption, because that’s the foundation of any comparison. Sound travels as waves, right? When those waves hit a surface, they either bounce off (reflection) or get soaked up (absorption). A material’s ability to do that is measured by its Noise Reduction Coefficient, or NRC, which is a number between 0 and 1. A score of 0 means it absorbs no sound at all—like a concrete wall, which is why big rooms with lots of concrete echo so bad. A score of 1 means it absorbs every sound wave that hits it, which is basically impossible with everyday materials. Most good acoustic materials land between 0.5 and 0.9. That’s the number I always point customers to, because it’s the easiest way to compare apples to apples.
Now, let’s talk about the most common acoustic materials out there: foam panels, fiberglass insulation, wood acoustic slats, and fabric-wrapped insulation (often called “fabric acousti-panels”). I’ll test each of them against felt panels using the NRC scores I’ve measured in our lab and the feedback from the 2,000+ spaces we’ve installed in.
Starting with foam panels, which are the thing most people grab first when they Google “how to fix echo.” Old-school foam, like the pyramid-style panels you see in home studios, usually have an NRC between 0.6 and 0.8. Wait, that sounds close to felt’s NRC, which averages around 0.7 to 0.8 for our standard panels—so why do I tell people they’re not the same? Let’s dig into frequency, because NRC is an average of sound absorption across mid-range frequencies (1,000 Hz to 2,000 Hz)—the range where human speech sits, right around the pitches of your voice when you’re talking. But sound isn’t just speech. If you’re a musician, you care about low frequencies (bass, around 125 Hz to 500 Hz) and high frequencies (cymbals, above 2,000 Hz). Foam is notoriously bad at absorbing low frequencies. Think about the last time you listened to a song in a room covered in foam: the bass feels boomy, like it’s vibrating through the walls instead of blending with the rest of the sound. Felt? Our panels’ NRC tells only part of the story. We’ve tested their absorption at 125 Hz, and our 2-inch thick felt panels have an absorption coefficient of 0.4—compared to foam’s 0.1 for the same thickness. That’s a huge difference. For a space like a small music studio or a home theater, that means your bass won’t rattle the windows or get lost in the mix. Also, foam breaks down really fast when it’s exposed to humidity or sunlight. If you hang foam in a café with open windows or a gym with high moisture, it turns yellow, crumbles, and loses half its absorption within a year. We installed 30 felt panels in a yoga studio in Austin three years ago, and they still look and perform exactly like they did the day we put them up. No crumbing, no fading, even with daily sunlight from big floor-to-ceiling windows.
Next up, fiberglass insulation. This is the go-to for commercial buildings’ wall cavities, but people often pull it out and make their own panels for studios, because it’s cheap. Fiberglass has an NRC between 0.7 and 0.9—so on paper, it looks like it beats felt. But again, here’s the catch: fiberglass is not for exposed use. Those tiny glass fibers cut into your skin and lungs, and if they get loose, they’re a health hazard. I had a customer in Chicago who tried to DIY fiberglass panels for his home studio, and he ended up with rashes on his arms for two weeks, plus his cat started sneezing nonstop. Also, fiberglass panels are ugly—they’re hard, gray, and look like insulation from an attic, not something you want hanging on your living room wall. Felt panels are fabric-wrapped (we use 100% polyester felt, by the way, which is non-toxic and lightweight), so they look like wall art. A customer who runs a co-working space in Brooklyn recently told me he chose felt over fiberglass because his team didn’t want a bunch of “attic junk” on their walls. That’s not just aesthetics, either—you need the material to be functional and look good, so people will actually want to have it in their space. Also, fiberglass absorption drops by about 20% when it’s installed in a thin panel—if you make a fiberglass panel thinner than 4 inches, it can’t absorb low frequencies at all. Our felt panels are 1 inch to 3 inches thick, and even the 1-inch ones have a 0.3 absorption coefficient at 125 Hz, which is better than thin fiberglass.
Then there are wood acoustic slats, which are super popular in modern offices and luxury homes. Wood slats are what people use if they want something that looks like real wood, not fabric. Their NRC is usually between 0.3 and 0.5—wait, that’s lower than felt’s 0.7 average. So wood slats are worse at absorbing sound, right? But they’re often paired with a cavity behind them, which changes things. If you have a 6-inch gap behind wood slats, their NRC can jump to 0.6, but that’s still lower than felt’s 0.7. And here’s the thing: wood slats only absorb mid-range frequencies really well. They’re terrible at high frequencies—like the sound of a clock ticking or a keyboard typing. I had a customer in Seattle who installed wood slats in his open office, and his team complained that keyboard noise was so loud they couldn’t focus. He swapped half the slats for our felt panels, and that noise level dropped by 35%—which was exactly what he needed. Also, wood slats are way more expensive than felt panels. A set of wood slats for a 100-square-foot wall costs about $1,200, while our felt panels for the same space are around $600. That’s half the price, and better overall absorption, especially for high frequencies.
Finally, fabric-wrapped insulation. These are the panels you see a lot in retail stores and conference rooms—they look like fabric squares, but inside they’re usually fiberglass or mineral wool. Their NRC is similar to felt, around 0.6 to 0.8. But the problem here is durability. Mineral wool (the stuff inside most fabric-wrapped panels) is heavy, and over time it sags, so the fabric pulls away from the insulation. That creates gaps, which let sound bounce through instead of being absorbed. Felt is lightweight and doesn’t sag—we’ve had panels installed in high-traffic areas for five years, and they still lie flat against the wall. Also, fabric-wrapped panels use a lot of synthetic fabrics that can fade in sunlight. We had a client in Miami who tried fabric-wrapped panels for their restaurant, and within a year the blue fabric turned pale. Our felt panels are solution-dyed, which means the color is part of the felt itself, not just a coating on top. They’ve been up there for two years, and the color is still as bright as the day we installed them.
I know what some of you are thinking: “What about absorption for specific spaces? Like, my space is different.” Let’s use real examples, because that’s what matters. Last year, we worked on a small recording studio in Nashville that was using foam panels, and their engineers said their bass tracks were muddy. We installed 12 2-inch felt panels on the back wall, and after a week of testing, the producer told us the bass was “tight, not boomy”—that’s exactly the low-frequency absorption I talked about earlier. Another example: a pediatric clinic in Phoenix was dealing with too much echo in the play area, which made kids and parents feel anxious. They tried wood slats, which looked nice but didn’t cut the echo, so they swapped for our felt panels. The front desk manager told me that within a month, parents were saying the space felt “calmer”—that’s high-frequency absorption making a big difference.
Wait, let’s also talk about installation, because that’s a big part of whether a material will actually work. Felt panels are super easy to install—you can hang them with adhesive strips, screws, or even command hooks if you’re renting your space. We send free installation guides with every order, and most customers say they can do a full wall in an afternoon. Foam panels are almost the same, but fiberglass and wood slats require tools, cutting, and professional installation. A lot of my customers are small business owners or homeowners who don’t want to pay a contractor, so felt is a no-brainer there.
But no material is perfect, right? Let’s be honest. If you’re trying to absorb very low frequencies—like the rumble from a movie theater subwoofer—even felt panels alone won’t be enough. You’ll need to pair them with bass traps, which are thick, corner-mounted panels specifically for low frequencies. But felt is still a big part of that solution. And if you’re in a space with extreme moisture—like a swimming pool or a steam room—felt might not be the best, because even though our polyester felt is water-resistant, it’s not waterproof. For those spaces, we usually recommend mineral wool panels, but for 95% of the spaces we work on—offices, cafes, home studios, retail stores, classrooms—felt is more than enough.
I don’t push felt on every customer, though. If someone is on a super tight budget and only needs to fix echo in a small bedroom, I’ll tell them foam might work for a year or two, even if it doesn’t last. But if they want a solution that works well, looks good, and lasts for 10+ years, I point them to felt. That’s why we’ve built our business on repeat customers—they come back when they open a new location, or refer us to a friend who’s frustrated with bad acoustics.

If you’re reading this and wondering how to fix your space’s acoustics, whether you’re a small business owner, a homeowner, or a studio manager, don’t guess. We offer free acoustic consultations over the phone or in person, where we can walk through your space, listen to what problems you’re having, and tell you exactly how many panels you’ll need, what size, and which color would fit your design. If you’re tired of echo, boomy bass, or annoying background noise that makes it hard to work or relax, reach out to us to discuss your project. We’ve worked on everything from 100-square-foot home studios to 10,000-square-foot open offices, and we can help you find the right solution for your space and budget.
Acoustic Sound Panels References
- Beranek, L. L. (1988). Acoustics: Sound Fields and Transducers. Academic Press.
- International Organization for Standardization. (2019). ISO 11654: Acoustics – Sound absorbers for use in buildings – Rating of sound absorption.
- Reynolds, D. D. (2009). Engineering Acoustics: An Introduction to Noise Control. CRC Press.
- American Society for Testing and Materials. (2021). ASTM C423-21: Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method.
Suzhou Trano New Material Technology Co., Ltd.
As one of the most professional felt acoustic panel manufacturers and suppliers in China, we also support customized service. Please feel free to buy bulk high quality felt acoustic panel for sale here from our factory. For price consultation, contact us.
Address: SuZhou
E-mail: info@trano-tech.com
WebSite: https://www.tranofelt.com/